Fuel Gear Pump Model KFP-12/24 can be mounted on any flat surface. Fit the pump in a dry, well ventilated position where there is full access for service. If installed in a vertical position the motor must be above the pump head. Use the rubber grommets provided to minimise vibration, do not overtighten the mounting screws. Secure 14mm (½”) id hose direct to the discharge ports using stainless steel hose clamps. Use spiral reinforced hose (with a smooth internal bore) that will not collapse under suction, or rigid or semi rigid pipework systems. The pipework must be compatible with the liquid being pumped. Pipe runs should be kept as straight and short as possible, avoiding rising and dipping over obstructions. Fit a filter on the inlet to prevent debris from entering the pump.

FEATURES & BENEFITS

Flow rate: Nominal 14 Litres/min (3.5 gallons/min) at 1500rpm
Self-priming from dry up to 1m (3ft)

Model No.: KFP series

Maximum viscosity 150Cs.
Inlet Filter Included.
Simple design means fewer wearing parts.
Ideal for water, oil and diesel transfer.
Meets USCG 183.410.
ISO 8846 MARINE (Ignition protection).
Reversible self-priming
Compact size with exceptional flow rate (3.7GPM / 14.0 LPM)
Powerful reversible pumps specially designed to be used with oils.

Features & Benefits
Seamless Shell Design
Thermally Protected Motor
High Quality Efficient Motor
Self-priming
Stainless Steel Shaft

Typical Applications
Extreme duty
Transmission fluid
(Diesel, Lubricant and viscous liquids)
Industrial use

PUMP
Liquid Temperature
140°F (60°C) Max.
Priming Capabilities
Not needed flooded suction
Power
3.8 amps max current draw
Max Pressure
Not needed
Inlet/Outlet Ports
3/8" FNPT (9.52 mm)
thread fitting
Weight
5.46 lbs (2.48 kg)

MOTOR
Type
High quality seamless design
that is thermally protected
Leads
Wire leads
Temperature Limits
140°F (60°C) Max.
Duty Cycle
Intermittent
Voltage
12v/24v

TECHNICAL SECIFICATIONS

Ports: 3/8” Male JIC
Amps: 3.8A@12v - 2.0A@24v
Flow Rate: 3.7 GPM / 14.0 LPM
Self priming: 5 feet (wet gears)
Lift: 15 feet
Pump body: Brass
Gears: Bronze
Shaft: Stainless Steel
Seal: Fluoroelastomer lip seal
Motor: DC 12v or 24v

STANDARD PUMP CONFIGURATIONS

Model	GPM/LPM	Dimensions	gears	Ports	Lead	Molded	Voltage	Max Draw(A)
KFP-12	3.7/14.0	8.46" x 5.31" x 4.33" 215 x 135 x 110mm	copper	3/8" FNPT	Yes	N/A	12V	3.8
KFP-24	3.7/14.0	8.46" x 5.31" x 4.33" 215 x 135 x 110mm	copper	3/8" FNPT	Yes	N/A	24V	2.0

PRESSURE-FLOW CURVE

DIMENSIONS DRAWINGS

IMAGE GALLERY

CHEMICAL RESISTANCE

Chemical Resistance Code

Max Temperature Resistance Code

A —— Excellent

B —— Good

C —— Ordinary

× —— Unacceptable

－ —— Unusable

1 —— 20℃(68F)

2 —— 40℃(104F)

3 —— 60℃(140F)

4 —— 80℃(176F)

5 —— 100℃(212F)

6 —— 120℃(248F)

CHEMICAL		MATERIAL
CHEMICAL		PP	PTFE	FKM	NBR	EPDM	95 Ceramic
Sulfuric Acid	0-10%	A4	A6	A6	B2	A4	A5
	10-75%	A3	A6	A4	X	A3	A5
	75-100%	B2	A4	A4	－	B2	A5
Nitric Acid	10%	A3	A5	A5	X	A2	A5
	30%	A2	A6	A6	X	A2	A5
	50%	B2	A3	A1	X	X	A5
Hydrochloric Acid	0-25%	A4	A6	A3	B1	C3	A5
Hydrochloric Acid	25-40%	A4	A6	A2	X	C2	A5
Hydrofluoric Acid	10%	B2	A6	A3	X	A3	－
	30%	C2	A6	A4	－	B3	－
	60%	X	A6	A4	－	C2	－
Acetic Acid	20%	A2	A6	B1	B2	A2	A5
Acetic Acid	80%	B1	A6	X	－	－	A5
Sodium Hydroxide	20%	A3	A6	B1	B2	A3	－
Sodium Hydroxide	50%	A3	A6	X	B1	A4	－
Bromine Water		C1	A3	A2	－	X	A1
Ethyl Alcohol		A2	A3	A3	X	B3	A3
Ketone		A2	A6	X	－	B2	A3
Freon 12		X	A6	A1	X	B1	A4
Aluminum Chloride		A4	A6	A5	B4	A4	A4
Ammonia Liquid		A1	A6	C1	B4	B3	A3
Aqua Regia		C2	A5	B2	－	C2	A4
Formaldehyde		A4	A6	A4	X	A4	A4
Gasoline		X	A6	B3	B3	X	A4
Kerosene		A1	A6	A1	B1	X	A4
Methyl Alcohol		A3	A6	B2	B4	A3	A5
Toluene		C1	A4	B1	－	X	A5
Trichloroethylene		C1	A6	A1	－	X	A4
Xylene		X	A6	B1	－	X	A5
Nitric Acid Anhydrous		C1	A3	A1	－	X	A5
Oleum		X	A6	A4	－	X	A5
Potassium Hydroxide		A4	A6	B1	C2	A5	－

USAGE SCOPE

Widely used in general industrial equipment, medical equipment, chemical equipment, agricultural (lawns and gardens), tourist vehicles, special vehicles, ships, beverage, vehicle cleaning, carpet cleaning, floor cleaning, water purification and water treatment equipment.
1. Production of agricultural use electric sprayer, pressure sprayer can also be hand modified electric sprayer (pressure sprayer in hand directly on the micro-pumps, adding a battery or hand lamp can be).
2. Solve vehicles, ships, yachts, boats, etc. in use diet, wash, shower, toilet, wash water.
3. Food and beverage processing and handling equipment, to achieve the transfer of liquid food, distribution, filling and so on.
4. Domestic water supply. For example, water-saving toilet, water-saving toilet, electric toilet, pressurized water system.
5. Solar energy industry.
6. Water purification industry. For example, purification equipment, water treatment equipment, drinking fountains, water machines. For towel disposal, drinking fountains, Coke machines, juice machines, dishwashers, disinfection machines, solar bonsai, car washing and other manufacturers supporting the glass.
7. Other liquid transfer needs, as well as measurement of spray equipment and systems. For example, garbage trucks, water truck, carpet cleaning equipment, floor cleaning equipment, cleaning equipment, vehicles, road construction equipment, medical equipment, chemical equipment, chemical equipment, disinfection equipment, cooling systems, pressurization systems.

Inquiry Cart 0